VERSION 1

# Supports all alphanumeric ASCII, and ' ', '_', '-', '+' - can also be NULL
TRACKNAME Super 6

# Can be POLY, DRUM, MPE, or NULL
TYPE NULL

# Can be A, B, C, D, USBD, USBH, CVGx (x between 1&4), CVx, Gx, or NULL
OUTPORT NULL

# Can be x (between 1-16), or NULL -- this is ignored if output port is not MIDI
OUTCHAN NULL

# Can be NONE, ALLACTIVE, A, B, USBH, USBD, CVG, or NULL
INPORT NULL

# Can be x (between 1-16), ALL, or NULL. This definition will be ignored if INPORT is NONE, ALLACTIVE or CVG
INCHAN NULL

# This defines the default 'MAX RATE' for automation lanes.
# Can be NULL, 192, 96, 64, 48, 32, 24, 16, 12, 8, 6, 4, 3, 2, 1
MAXRATE NULL

# DRUMLANES
# Syntax: ROW:TRIG:CHAN:NOTENUMBER NAME
# ROW must be between 1 and 8
# TRIG can be between 0 and 127, or NULL
# CHAN can be a number between 1 and 16, Gx, CVx, CVGx (x between 1 and 4), or NULL
# NOTENUMBER can be between 0 and 127, or NULL
# NAME supports all alphanumeric ASCII, and ' ', '_', '-', '+' - can also be NULL
# Please note this section will be discarded for tracks which are not DRUM tracks
[DRUMLANES]
[/DRUMLANES]


# PC
# Syntax: NUMBER NAME
# number must be either:
#   - A number (for simple PC)
#   - Three numbers, delimited by ':', which represent PC:MSB:LSB. You can put 'NULL' to not set the MSB/LSB.
# PC must be between 1...128
# MSB/LSB must be between 0...127
[PC]
[/PC]


# CC
# Syntax: CC_NUMBER NAME or CC_NUMBER:DEFAULT=xx NAME
# DEFAULT_VALUE must be a valid number between 0 and 127
[CC]
82 Arp range
90 Seq length
89 Seq rec mode
87 Hold
86 Arp or seq on
85 Arp or seq mode
83 Arp or seq swing
15 Chorus II on
14 Chorus I on
22 DDS Env 1 amount
23 DDS modulator destination
21 DDS LFO 1 amount
76 DDS pitch bend amt
30 DDS 1 range
31 DDS 2 waveform
34 DDS 2 range
35 DDS 2 tune
70 DDS LFO 2 amt
36 DDS 2 mode
29 DDS 1 waveform
12 Delay time
91 Delay level
13 Delay feedback
57 Env 2 decay
55 Env 1 sustain
54 Env 1 decay
53 Env 1 attack
52 Env 1 hold
51 Env 1 keytrack
50 Env 1 mode
73 Env 2 attack
72 Env 2 release
58 Env 2 sustain
56 Env 1 release
127 Poly mode on
1 Modulation lever
3 Tempo
4 Foot controller
5 Portamento time
6 Data entry MSB
38 LSB for Control 6 data entry
59 Manual
61 Performance control dest
64 Sustain pedal
96 Data increment
97 Data decrement
98 NRPN LSB
99 NRPN MSB
100 RPN LSB
101 RPN MSB
120 All sound off
121 Reset all controllers
122 Local control on off
123 All notes off
124 Omni mode off
125 Omni mode on
126 Mono mode on
16 LFO 1 waveform   HF mode
62 LFO 2 rate
20 LFO 1 mode
19 LFO 1 L R phase
18 LFO 1 delay
17 LFO 1 rate
63 LFO 2 delay
60 LFO 2 trigger src
24 Super mode
28 Cross mod
27 PWM SWM src
37 Ocsillator Mix split point
26 PWM SWM
78 Voice assign mode
79 Union size
80 Binaural mode on
81 Sync
25 PW Detune
49 VCA env mode
48 VCA dynamics
7 VCA env level
44 VCF env src
43 VCF keytrack
41 VCF drive
40 VCF HPF mode
46 VCF LFO 1 amt
47 VCF LFO 2 amt
71 VCF resonance
77 VCF pitch bend amt
75 VCF LFO 2 amt
92 VCF LFO 1 amt
74 VCF cutoff frequency
45 VCF env amt

[/CC]

# CC Pair
# Syntax: CC_MSB:CC_LSB NAME or CC_MSB:CC_LSB:DEFAULT=xx NAME
# DEFAULT_VALUE must be a valid number between 0 and 16383
[CC_PAIR]

[/CC_PAIR]

# NRPN
# Syntax: "MSB:LSB:DEPTH NAME" or "MSB:LSB:DEPTH:DEFAULT=xx NAME"
# Lsb & msb should be between 0 and 127
  # Note: LSB can be over 127 ONLY if MSB is 0 or omitted
  # e.g. '0:1026:7 FOO', or ':2000:7 BAR' 
  # the examples above would be equivalent to '8:2:7 FOO' and '15:80:7 BAR' respectively
# DEPTH can be 7 or 14
# For NRPN: DEFAULT_VALUE must be a valid number, either between 0 and 127 (for 7 bit NRPNs) or between 0 and 16383 (for 14bit NRPNs)
[NRPN]

[/NRPN]


# ASSIGN
# Syntax: POT_NUMBER TYPE:VALUE or POT_NUMBER TYPE:VALUE DEFAULT=DEFAULT_VALUE
# POT_NUMBER must be between 1 and 8
# TYPE can be "CC", "PB" (pitchbend), "AT" (aftertouch), "CV", "NRPN", or "NULL" (this won't assign the pot).
# Non explicitly-defined pots will be considered "NULL"
# VALUE VALIDATION
#### For CC: Value must be a valid number between 0 and 119
#### For PB and AT, any text after the TYPE will be ignored
#### For CV, value must be between 1 and 4
#### For NRPN, value must be MSB:LSB:DEPTH, with both lsb & msb bebtween 0 and 127, and DEPTH being either 7 or 14
# DEFAULT VALUE
#### For CC: DEFAULT_VALUE must be a valid number between 0 and 127
#### For PB: DEFAULT_VALUE must be a valid number between 0 and 16383
#### For NRPN: DEFAULT_VALUE must be a valid number, either between 0 and 127 (for 7 bit NRPNs) or between 0 and 16383 (for 14bit NRPNs)
#### For CV: DEFAULT_VALUE must be either a valid number between 0 and 65535, or a voltage between -5V and 5V, e.g. "-4.25V" or "1.7V"
#### Please note default value will be ignored for PB and AT messages.
[ASSIGN]
[/ASSIGN]


# AUTOMATION
# Syntax: TYPE:VALUE
# TYPE can be "CC", "PB" (pitchbend), "AT" (aftertouch), "CV", or "NRPN"
# VALUE VALIDATION
#### For CC: Value must be a valid number between 0 and 119
#### For PB and AT, any text after the TYPE will be ignored
#### For CV, value must be between 1 and 4
#### For NRPN, value must be MSB:LSB:DEPTH, with both lsb & msb bebtween 0 and 127, and DEPTH being either 7 or 14
# NOTE: You are limited to 64 automation lanes
[AUTOMATION]
[/AUTOMATION]


# This section will be readable from Hapax.
[COMMENT]

[/COMMENT]