VERSION 1

# Supports all alphanumeric ASCII, and ' ', '_', '-', '+' - can also be NULL
TRACKNAME Take 5

# Can be POLY, DRUM, MPE, or NULL
TYPE NULL

# Can be A, B, C, D, USBD, USBH, CVGx (x between 1&4), CVx, Gx, or NULL
OUTPORT NULL

# Can be x (between 1-16), or NULL -- this is ignored if output port is not MIDI
OUTCHAN NULL

# Can be NONE, ALLACTIVE, A, B, USBH, USBD, CVG, or NULL
INPORT NULL

# Can be x (between 1-16), ALL, or NULL. This definition will be ignored if INPORT is NONE, ALLACTIVE or CVG
INCHAN NULL

# This defines the default 'MAX RATE' for automation lanes.
# Can be NULL, 192, 96, 64, 48, 32, 24, 16, 12, 8, 6, 4, 3, 2, 1
MAXRATE NULL

# DRUMLANES
# Syntax: ROW:TRIG:CHAN:NOTENUMBER NAME
# ROW must be between 1 and 8
# TRIG can be between 0 and 127, or NULL
# CHAN can be a number between 1 and 16, Gx, CVx, CVGx (x between 1 and 4), or NULL
# NOTENUMBER can be between 0 and 127, or NULL
# NAME supports all alphanumeric ASCII, and ' ', '_', '-', '+' - can also be NULL
# Please note this section will be discarded for tracks which are not DRUM tracks
[DRUMLANES]
[/DRUMLANES]


# PC
# Syntax: NUMBER NAME
# number must be either:
#   - A number (for simple PC)
#   - Three numbers, delimited by ':', which represent PC:MSB:LSB. You can put 'NULL' to not set the MSB/LSB.
# PC must be between 1...128
# MSB/LSB must be between 0...127
[PC]
[/PC]


# CC
# Syntax: CC_NUMBER NAME or CC_NUMBER:DEFAULT=xx NAME
# DEFAULT_VALUE must be a valid number between 0 and 127
[CC]
1 MOD Wheel
2 Breath
3 BPM
4 Foot Controller
5 Glide Mode
6 Data Entry MSB
7 Master Volume
8 OSC1 Octave04
9 OSC1 Fine Freq
10 OSC1 Shape
11 Expression Pedal
12 Voice Volume
13 OSC2 Octave04
14 OSC2 Fine Freq
15 OSC2 Shape
16 FX ON Off01
17 FX Type08
18 FX Depth MIX
19 FX Time
20 FX Feedback Misc
21 FX Clock Sync ON Off01
22 FX Clock Sync Rate010
23 Reverb ON Off01
24 Reverb WET DRY MIX
25 Reverb Size
26 Reverb Predelay
27 Reverb Decay
28 Reverb Tone
29 1 Oct01
30 2 Oct01
31 Unison ON Off01
32 Bank Select LSB
33 Filter Cutoff
34 Filter Resonance
35 Filter Drive
36 Filter KEY Tracking
37 Vintage
38 Data Entry LSB
39 OSC Sync01
40 OSC1 Level
41 OSC2 Level
42 SUB OSC Level
43 Noise Level
44 FM ON OF01
45 ENV1 Delay
46 ENV1 Attack
47 ENV1 Decay
48 ENV1 Sustain
49 ENV1 Release
50 ENV1 Amount
51 ENV1 VEL ON Off01
52 ENV2 DEL
53 ENV2 Attack
54 ENV2 Decay
55 ENV2 Sustain
56 ENV2 Release
57 ENV2 Amount
58 ENV2 VEL ON Off01
59 ARP ON Off01
60 ARP Mode02
61 ARP Octave02
62 ARP Repeats03
63 Clock Divide07
64 Sustain Pedal
65 OSC1 Glide Rate
66 OSC2 Glide Rate
67 Distortion
68 Glide ON Off01
69 ENV Routing02
70 Unison Voice Count05
71 Unison Detune07
72 Unison KEY Mode02
73 Unison Retrigger01
74 Brightness
75 LFO1 Freq
76 LFO1 Amount
77 LFO1 Shape04
78 LFO1 Sync ON Off01
79 LFO1 Note Reset01
80 LFO2 Freq
81 LFO2 Amount
82 LFO2 Shape04
83 LFO2 Sync ON Off01
84 LFO2 Note Reset01
85 Pitch Bend Range Up012
86 Pitch Bend Range Down024
87 OSC1 KEY Tracking ON Off01
88 OSC2 KEY Tracking ON Off01
89 KEY Split Note044

[/CC]

# CC Pair
# Syntax: CC_MSB:CC_LSB NAME or CC_MSB:CC_LSB:DEFAULT=xx NAME
# DEFAULT_VALUE must be a valid number between 0 and 16383
[CC_PAIR]

[/CC_PAIR]

# NRPN
# Syntax: "MSB:LSB:DEPTH NAME" or "MSB:LSB:DEPTH:DEFAULT=xx NAME"
# Lsb & msb should be between 0 and 127
  # Note: LSB can be over 127 ONLY if MSB is 0 or omitted
  # e.g. '0:1026:7 FOO', or ':2000:7 BAR' 
  # the examples above would be equivalent to '8:2:7 FOO' and '15:80:7 BAR' respectively
# DEPTH can be 7 or 14
# For NRPN: DEFAULT_VALUE must be a valid number, either between 0 and 127 (for 7 bit NRPNs) or between 0 and 16383 (for 14bit NRPNs)
[NRPN]

[/NRPN]


# ASSIGN
# Syntax: POT_NUMBER TYPE:VALUE or POT_NUMBER TYPE:VALUE DEFAULT=DEFAULT_VALUE
# POT_NUMBER must be between 1 and 8
# TYPE can be "CC", "PB" (pitchbend), "AT" (aftertouch), "CV", "NRPN", or "NULL" (this won't assign the pot).
# Non explicitly-defined pots will be considered "NULL"
# VALUE VALIDATION
#### For CC: Value must be a valid number between 0 and 119
#### For PB and AT, any text after the TYPE will be ignored
#### For CV, value must be between 1 and 4
#### For NRPN, value must be MSB:LSB:DEPTH, with both lsb & msb bebtween 0 and 127, and DEPTH being either 7 or 14
# DEFAULT VALUE
#### For CC: DEFAULT_VALUE must be a valid number between 0 and 127
#### For PB: DEFAULT_VALUE must be a valid number between 0 and 16383
#### For NRPN: DEFAULT_VALUE must be a valid number, either between 0 and 127 (for 7 bit NRPNs) or between 0 and 16383 (for 14bit NRPNs)
#### For CV: DEFAULT_VALUE must be either a valid number between 0 and 65535, or a voltage between -5V and 5V, e.g. "-4.25V" or "1.7V"
#### Please note default value will be ignored for PB and AT messages.
[ASSIGN]
[/ASSIGN]


# AUTOMATION
# Syntax: TYPE:VALUE
# TYPE can be "CC", "PB" (pitchbend), "AT" (aftertouch), "CV", or "NRPN"
# VALUE VALIDATION
#### For CC: Value must be a valid number between 0 and 119
#### For PB and AT, any text after the TYPE will be ignored
#### For CV, value must be between 1 and 4
#### For NRPN, value must be MSB:LSB:DEPTH, with both lsb & msb bebtween 0 and 127, and DEPTH being either 7 or 14
# NOTE: You are limited to 64 automation lanes
[AUTOMATION]
[/AUTOMATION]


# This section will be readable from Hapax.
[COMMENT]

[/COMMENT]